The evolution of the microstructure and properties of ageable Al-Si-Zn-Mg alloy during the recycling of milling chips through powder metallurgy
Artículo de revista
2020
Elsevier
Although long/continuous metallic chips are easily recycled by melting, this is not the casefor discontinuous milling chips. The present study aimed to reduce waste generation andto facilitate the use of this byproduct in order to obtain a metallic-oxide composite. Chipswere collected after machining Al-Si-Zn-Mg alloy parts, and powders were obtained throughgrinding processes. Grinding was performed at 45, 69, and 94 h, with grinding bodies/chipsvolume ratios of 6:1, 8:1, 10:1 and 12:1. The resulting powders were characterized by scanningelectron microscopy, laser granulometry, and X-ray diffraction. After grinding, the parti-cles were compacted and sintered, and hardness was evaluated. It was found that metallicpowder is formed through plastic deformation, hardening, fracture, and dynamic recrystal-lization. It was possible to obtain samples with lower apparent density and higher hardnessby powder metallurgy from Al-Si-Zn-Mg alloy chips than from the bulk. Powder was obtainedafter grinding, and samples were obtained by compacting and sintering. The higher hard-ness value was attributed to the presence of Al2O3formed in the particles during grinding,which acts as a second reinforcing phase in the sintered samples, and as a retardant ofintermetallic phase growing Aunque las virutas metálicas largas / continuas se reciclan fácilmente por fusión, este no es el caso de las virutas de molienda discontinuas. El presente estudio tuvo como objetivo reducir la generación de residuos y facilitar el uso de este subproducto para obtener un compuesto de óxido metálico. Las virutas se recogieron después de mecanizar piezas de aleación de Al-Si-Zn-Mg y los polvos se obtuvieron mediante procesos de molienda. La trituración se realizó a las 45, 69 y 94 h, con relaciones de volumen de cuerpos de trituración / virutas de 6: 1, 8: 1, 10: 1 y 12: 1. Los polvos resultantes se caracterizaron mediante microscopía electrónica de barrido, granulometría láser y difracción de rayos X. Después de la molienda, las partículas se compactaron y sinterizaron y se evaluó la dureza. Se encontró que el polvo metálico se forma mediante deformación plástica, endurecimiento, fractura y recristalización dinámica. Fue posible obtener muestras con menor densidad aparente y mayor dureza mediante pulvimetalurgia a partir de virutas de aleación de Al-Si-Zn-Mg que a granel. El polvo se obtuvo después de la trituración y las muestras se obtuvieron por compactación y sinterización. El mayor valor de dureza se atribuyó a la presencia de Al2O3 formado en las partículas durante la molienda, que actúa como una segunda fase de refuerzo en las muestras sinterizadas y como retardador del crecimiento de la fase intermetálica.
Descripción:
The evolution of the microstructure and properties of ageable Al-Si-Zn-Mg alloy during the recycling of milling chips through powder metallurgy _ Elsevier Enhanced Reader.pdf
Título: The evolution of the microstructure and properties of ageable Al-Si-Zn-Mg alloy during the recycling of milling chips through powder metallurgy _ Elsevier Enhanced Reader.pdf
Tamaño: 7.257Mb
PDFLEER EN FLIP
Título: The evolution of the microstructure and properties of ageable Al-Si-Zn-Mg alloy during the recycling of milling chips through powder metallurgy _ Elsevier Enhanced Reader.pdf
Tamaño: 7.257Mb
PDFLEER EN FLIP